#  >>>     Bafang CAN bus motor parameters settings file        <<<
#  >>> K1 Flash v1.42   M300,M420,M500,M510,M560,M600,M620,M820 <<<
#  ****************************************************************

#  This script will be executed after power up of K1 Flash 
#  with SD card inserted - Green LED is blinking.

#  After connecting motor, device will setup your motor 
#  controller parameters (only what motor supports).
#  Green LED steady - sucesfully set and you can disconnect K1

#  Important - Commands needs to be entered exactly, without
#  any misstyping (first 5 characters are important).
#  Otherwise device will ignore this line.

#  Add "cage" # character to comment out whole line and disable the command.

#  Activate this setup as following:
#  1. Insert SD card in. (This file needs to be in root 
#     directory of SD card and FAT16 is needed).
#  2. Power on K1 Flash over USB-C (power bank, mobile, charger)
#  3. Connect to Bafang CAN motor (5 pin green connector 
#     with "house shape" - unplug from LCD display/buttons)
#  4. You can disconnect after few seconds - when LED goes 
#     steady Green - the following parameters are set:
#  ----------------------------------------------------------

#  >>>Basic parameter commands works with ALL Bafang CAN bus motors
#     including Bafang CAN hub motors :

#  Speed limit. 
#  With M510 FC2.0 and M560 throtle speed limit is hardcoded (32 or 45 kmh). 

Speed=45

#  Wheel size in inches - does not play any role on Bafang CAN
#  controllers, just to show this info on display. For 27.5 put with dot.

Wheel=29

#  Circumference of rear wheel in mm, motor is counting actual
#  speed out of this number, check against GPS

Circumference=2230

#  ---------------------------------------------------------------
#  >>>Following commands works with M510, M560, M820, M620 (firmware v1.2) motors:

#  Global acceleration, 1 to 8, 8 is max acceleration. (M510 FC2.0 and M560 is ignoring this setting) 
Acceleration=8

#  How fast motor starts to assist on initial pedal turn. 
#  0 to 13, 0 is fastest response. New motors and firmwares are taking Start-up angle in degree instead.
Startup Angle=1

#  Max current(Power) in % per each PAS level. 
#  Note: For M510 FC2.0 are defaults 50,75,100,100,100 - does make sense with Support level %
Max Current Map=20,32,46,72,100

#  Max caddence in % (aka Speed Limit % - which is confusing, does not have anything with speed)
RPM Map=100,100,100,100,100

#  ---------------------------------------------------------
#  >>>Following commands works with M510 FC2.0, M560, M620 (firmware v12.3 750W) motors:

#  Torque multiplication to pedal torque (sensitivity to pedalling), 0 to 500%
#  Note: M510 FC2.0 defaults: 140,140,140,230,340
#  Also known as Assistance level %
Support level Map=140,160,180,230,340

#  Acceleration (current start Ramp-up time) per each PAS level
#  1 to 8, 8 is max acceleration, Ramp-up time: 1 = 2000ms, 7=500ms, 8=250ms
Map Acceleration=6,7,7,8,8

#  Startup angle in degree, if you have FC2.0 or M560 Startup Angle form previous section is ignored.
D StartUp Angle=12

#  ---------------------------------------------------------
#  Uncomment following command for Motor Calibration. 
#  Warning! Calibration will start in 5 second after
#  connecting to motor (number 5 at the end). Make sure chain
#  is down from chainring and you have battery charged!

#Calibration5

#  ---------------------------------------------------------
#  Note: You can run calibration by connecting over
#  terminal to K1 Flash - free "Serial USB Terminal" application
#  on Android phone. And also to set Speed, Circumference and Wheel
#  over terminal:
#  Example: s25   - Set Speed to 25 kmh
#           c2220 - Set Circumference to 2220 mm
#           w28   - Set Wheel size to 28 inch
#           cal   - Run Calibration. Put down chain before Calibration!

#  >>>  email: info@K1eBikes.com  <<<
#  >>> www.K1eBikes.com  Slovakia <<<